Birgit Nothdurft

Selective aggregation of gold and silver nanoparticles in water, leading to distinctly coloured states, can be achieved using particles with suitable ligands and bis(cyclodextrins) as the linking units.

In order to investigate the effect of grain boundaries on the mechanical response in the micrometer and submicrometer levels, complementary experiments and molecular dynamics simulations were conducted on a model bcc metal, tantalum. Microscale pillar experiments (diameters of 1 and 2 μm) with a grain size of ∼ 100-200 nm revealed a mechanical response characterized by a yield stress of ∼1,500 MPa. The hardening of the structure is reflected in the increase in the flow stress to 1,700 MPa at a strain of ∼0.35. Molecular dynamics simulations were conducted for nanocrystalline tantalum with grain sizes in the range of 20-50 nm and pillar diameters in the same range. The yield stress was approximately 6,000 MPa for all specimens and the maximum of the stress-strain curves occurred at a strain of 0.07. Beyond that strain, the material softened because of its inability to store dislocations. The experimental results did not show a significant size dependence of yield stress on pillar diameter (equal to 1 and 2 um), which is attributed to the high ratio between pillar diameter and grain size (∼10-20). This behavior is quite different from that in monocrystalline specimens where dislocation ‘starvation’ leads to a significant size dependence of strength. The ultrafine grains exhibit clear ‘pancaking’ upon being plastically deformed, with an increase in dislocation density. The plastic deformation is much more localized for the single crystals than for the nanocrystalline specimens, an observation made in both modeling and experiments. In the molecular dynamics simulations, the ratio of pillar diameter (20-50 nm) to grain size was in the range 0.2 to 2, and a much greater dependence of yield stress to pillar diameter was observed. A critical result from this work is the demonstration that the important parameter in establishing the overall deformation is the ratio between the grain size and pillar diameter; it governs the deformation mode as well as surface sources and sinks, which are only important when the grain size is of the same order as the pillar diameter.

Pulmonary delivery of nanocarriers for novel antimycobacterial compounds is challenging because the aerodynamic properties of nanomaterials are sub-optimal for such purposes. Here, we report the development of dry powder formulations for nanocarriers containing benzothiazinone 043 (BTZ) or levofloxacin (LVX), respectively. The intricacy is to generate dry powder aerosols with adequate aerodynamic properties while maintaining both nanostructural integrity and compound activity until reaching the deeper lung compartments. Microparticles (MPs) were prepared using vibrating mesh spray drying with lactose and leucine as approved excipients for oral inhalation drug products. MP morphologies and sizes were measured using various biophysical techniques including determination of geometric and aerodynamic mean sizes, X-ray diffraction, and confocal and focused ion beam scanning electron microscopy. Differences in the nanocarriers’ characteristics influenced the MPs’ sizes and shapes, their aerodynamic properties, and, hence, also the fraction available for lung deposition. Spay-dried powders of a BTZ nanosuspension, BTZ-loaded silica nanoparticles (NPs), and LVX-loaded liposomes showed promising respirable fractions, in contrast to zirconyl hydrogen phosphate nanocontainers. While the colloidal stability of silica NPs was improved after spray drying, MPs encapsulating either BTZ nanosuspensions or LVX-loaded liposomes showed the highest respirable fractions and active pharmaceutical ingredient loads. Importantly, for the BTZ nanosuspension, biocompatibility and in vitro uptake by a macrophage model cell line were improved even further after spray drying.

Summary The dragonfish is a voracious predator of the deep sea with an arsenal of tools to hunt prey and remain concealed. In contrast to its dark pigmented skin, the dragonfish is equipped with transparent teeth. Here, we establish the structure, composition, and mechanical properties of the transparent teeth for the first time. We find the enamel-like layer to consist of nanocrystalline hydroxyapatite domains (∼20 nm grain size) embedded in an amorphous matrix, whereas in the dentin layer the nanocrystalline hydroxyapatite coats nanoscale collagen fibrils forming nanorods. This nanoscale structure is responsible for the much-reduced Rayleigh light scattering, which is further ensured by the sufficiently thin walls. Here, we suggest that the nanostructured design of the transparent dragonfish teeth enables predatory success as it makes its wide-open mouth armed with saber-like teeth effectively disappear, showing no contrast to the surrounding blackness of the fish nor the background darkness of the deep sea.

BACKGROUND: Mollusc shells are commonly investigated using high-resolution imaging techniques based on cryo-fixation. Less detailed information is available regarding the light-optical properties. Sea shells of Haliotis pulcherina were embedded for polishing in defined orientations in order to investigate the interface between prismatic calcite and nacreous aragonite by standard materialographic methods. A polished thin section of the interface was prepared with a defined thickness of 60 µm for quantitative birefringence analysis using polarized light and LC-PolScope microscopy. Scanning electron microscopy images were obtained for comparison. In order to study structural-mechanical relationships, nanoindentation experiments were performed.RESULTS:Incident light microscopy revealed a super-structure in semi-transparent regions of the polished cross-section under a defined angle. This super-structure is not visible in transmitted birefringence analysis due to the blurred polarization of small nacre platelets and numerous organic interfaces. The relative orientation and homogeneity of calcite prisms was directly identified, some of them with their optical axes exactly normal to the imaging plane. Co-oriented "prism colonies" were identified by polarized light analyses. The nacreous super-structure was also visualized by secondary electron imaging under defined angles. The domains of the super-structure were interpreted to consist of crystallographically aligned platelet stacks. Nanoindentation experiments showed that mechanical properties changed with the same periodicity as the domain size.CONCLUSIONS:In this study, we have demonstrated that insights into the growth mechanisms of nacre can be obtained by conventional light-optical methods. For example, we observed super-structures formed by co-oriented nacre platelets as previously identified using X-ray Photo-electron Emission Microscopy (X-PEEM) [Gilbert et al., Journal of the American Chemical Society 2008, 130:17519–17527]. Polarized optical microscopy revealed unprecedented super-structures in the calcitic shell part. This bears, in principle, the potential for in vivo studies, which might be useful for investigating the growth modes of nacre and other shell types.

Molluscs have a well-deserved reputation for being expert mineralizers of various shell types such as nacre. Nacre is defined as regularly arranged layers and stacks of similar to 0.5 mu m thick aragonite platelets that are extracellularly formed within a complex mixture of organic matrix. The control of species-specific layer thickness by the animal is still enigmatic. Despite the recent findings on the periodic layer-by-layer structures of chitin layers and silk-like protein layers in nacre-type biominerals, little is known about how the interface is defined between two different layers. In this paper, we demonstrate the presence of covalently attached, hydrophobic amino acid side chains in the chitin matrix in the bivalve mollusc Mytilus galloprovincialis by the combination of infrared spectroscopy and mass spectroscopy. The accumulation of the modified chitin matrix at the interface is quantified by the critical aggregate concentration of the purified chitin matrix, which is approximately an order of magnitude smaller than that of pure chitin. Our finding suggests an active role of such chemically modified chito-oligosaccharides in the creation of a defined interface and guidance of the periodic matrix textures, which would result in unique material properties of natural mollusc shells.