Prof. Dr. Tobias Kraus

Ultrathin gold nanowires are unusual colloidal objects that assemble into bundles with line contacts between parallel wires. Each molecule in the contact line interacts with many ligand and solvent molecules. We used X-ray scattering and electron microscopy to study how these interactions control assembly.

Metal-based nanoparticle inks for printed electronics usually require sintering to improve the poor electron transport at particle-particle interfaces. The ligands required for colloidal stability act as insulating barriers and must be removed in a post-deposition sintering step. This complicates the fabrication process and makes it incompatible with many flexible substrates. Here, we bind a conjugated, electrically conductive polymer on gold nanorods (AuNRs) as a ligand. The polymer, poly[2-(3-thienyl)-ethyloxy-4-butylsulfonate)] (PTEBS), provides colloidal stability and good electron transport properties to stable, sintering-free inks. We confirm that the polymer binds strongly through a multidentate binding motif and provides superior colloidal stability in polar solvents over months by IR and Raman spectrometry and zeta potential measurements. We demonstrate that the developed ligand exchange protocol is directly applicable to other polythiophenes such as poly(3,4-ethylenedioxythiophene) polystyrene sulfonate (PEDOT:PSS). Films of AuNRs coated with above polymers reached conductivities directly after deposition comparable to conventional metal inks after ligand removal and retained their conductivity for at least one year when stored under ambient conditions.

Recently, the steady-state process of convective assembly has emerged as a viable production route for colloidal monolayers. The present study models the regions of particle assembly: Region I comprises convective concentration of a particle suspension in a liquid below a meniscus, Region II comprises permeation of fluid through the dense particle monolayer, and Region III comprises capillary densification. For each region, the dominant physics and nondimensional groups are identified, and quantitative models are derived to describe the evolution of microstructure in terms of the main process parameters. The concentration profile within the assembly zone of Region I is predicted, including the role of a concentration-dependent diffusion constant and the shape of the meniscus. The fluid flow through the assembled monolayer is treated in Region II, along with a stability calculation to reveal that isolated particle clusters do not survive on top of the monolayer. The physics of capillary crystallization is addressed in Region III, with an emphasis on the density of cracks that emerge. The Peclet number and Capillary number both play important roles but in different regions of the assembly process.

Citrate-stabilized gold nanoparticles (AuNP) agglomerate in the presence of hemoglobin (Hb) at acidic pH. The extent of agglomeration strongly depends on the concentration ratio [Hb]/[AuNP]. Negligible agglomeration occurs at very low and very high [Hb]/[AuNP]. Full agglomeration and precipitation occurs at [Hb]/[AuNP] corresponding to a Hb monolayer on the AuNP. Ratios just above and below this value lead to the formation of an unexpected phase: stable, microscopic AuNP-Hb agglomerates. We investigated the kinetics of agglomeration with dynamic light scattering and the adsorption kinetics of Hb on planar gold with surface acoustic wave phase measurements. Comparing agglomeration and adsorption kinetics leads to an explanation of the complex behavior of this nanoparticle-protein mixture. Agglomeration is initiated either when Hb bridges AuNP or when the electrostatic repulsion between AuNP is neutralized by Hb. It is terminated when Hb has been depleted or when Hb forms multilayers on the agglomerates that stabilize microscopic clusters indefinitely.

We report a versatile particle-based route to dense arrays of parallel submicron pores with high aspect ratio in silicon, and explore the application of these arrays in sensors, optics, and polymer micropatterning. Polystyrene (PS) spheres are convectively assembled on gold-coated silicon wafers and sputter-etched, resulting in well-defined gold disc arrays with excellent long-range order. The gold discs act as catalysts in Metal-Assisted Chemical Etching (MACE), yielding uniform pores with straight walls, flat bottoms and high aspect ratio. The resulting pore arrays can be used as robust antireflective surfaces, in biosensing applications, and as templates for polymer replica molding.

Medical X-ray imaging requires cost-effective and high-resolution flat-panel detectors for the energy range between 20 and 120 keV. Solution-processed photodetectors provide the opportunity to fabricate detectors with a large active area at low cost. Here, we present a disruptive approach that improves the resolution of such detectors by incorporating terbium-doped gadolinium oxysulfide scintillator particles into an organic photodetector matrix. The X-ray induced light emission from the scintillators is absorbed within hundreds of nanometres, which is negligible compared with the pixel size. Hence, optical crosstalk, a limiting factor in the resolution of scintillator-based X-ray detectors, is minimized. The concept is validated with a 256 × 256 pixel detector with a resolution of 4.75 lp mm−1 at a MTF = 0.2, significantly better than previous stacked scintillator-based flat-panel detectors. We achieved a resolution that proves the feasibility of solution-based detectors in medical applications. Time-resolved electrical characterization showed enhanced charge carrier mobility with increased scintillator filling, which is explained by morphological changes.

When a nanomaterial enters a biological system, proteins adsorb onto the particle surface and alter the surface properties of nanoparticles, causing drastic changes in physico-chemical properties such as hydrodynamic size, surface charge and aggregation state, thus giving a completely new and undefined physico-chemical identity to the nanoparticles. In the present work, we study the impact of the protein identity (molecular weight and isoelectric point) and the environmental conditions (pH and ionic strength) on the final physico-chemical properties of a model nanoparticle system, i.e. gold nanoparticles. Gold nanoparticles either form stable dispersions or agglomerate spontaneously when mixed with protein solutions, depending on the protein and the experimental conditions. Strikingly, the agglomerates redisperse to individually dispersed and colloidally stable nanoparticles, depending on the purification pH. The final protein coated nanoparticles exhibit specific stabilities and surface charges that depend on protein type and the conditions during its adsorption. By understanding the interactions of nanoparticles with proteins under controlled conditions, we can define the protein corona of the NPs and thus their physico-chemical properties in various media.

Vertically aligned silicon nanowire (VA-SiNW) arrays are emerging as a powerful new tool for gene delivery by means of mechanical transfection. In order to utilize this tool efficiently, uncertainties around the required design parameters need to be removed. Here, a combination of nanosphere lithography and templated metal-assisted wet chemical etching is used to fabricate VA-SiNW arrays with a range of diameters, heights, and densities. This fabrication strategy allows identification of critical parameters of surface topography and consequently the design of SiNW arrays that deliver plasmid with high transfection efficiency into a diverse range of human cells whilst maintaining high cell viability. These results illuminate the cell-materials interactions that mediate VA-SiNW transfection and have the potential to transform gene therapy and underpin future treatment modalities.

Control over particle self-assembly is a prerequisite for the colloidal templating of lithographical etching masks to define nanostructures. This work integrates and combines for the first time bottom-up and top-down approaches, namely, particle self-assembly at liquid?liquid interfaces and metal-assisted chemical etching, to generate vertically aligned silicon nanowire (VA-SiNW) arrays and, alternatively, arrays of nanoscale pores in a silicon wafer. Of particular importance, and in contrast to current techniques, including conventional colloidal lithography, this approach provides excellent control over the nanowire or pore etching site locations and decouples nanowire or pore diameter and spacing. The spacing between pores or nanowires is tuned by adjusting the specific area of the particles at the liquid?liquid interface before deposition. Hence, the process enables fast and low-cost fabrication of ordered nanostructures in silicon and can be easily scaled up. We demonstrate that the fabricated VA-SiNW arrays can be used as in vitro transfection platforms for transfecting human primary cells.

The ageing of spherical gold nanoparticles having 6-nm-diameter cores and a ligand shell of dodecanethiol is investigated under different storage conditions. Losses caused by agglomeration and changes in optical particle properties are quantified. Changes in colloidal stability are probed by analytical centrifugation in a polar solvent mixture. Chemical changes are detected by elementary analysis of particles and solvent. Fractionation occurs under all storage conditions. Ageing is not uniform but broadens the property distributions of the particles. Small-number statistics in the ligand shell density and the morphological heterogeneity of particles are possible explanations. Washing steps exacerbate ageing, a process that could not be fully reversed by excess ligands. Dry storage is not preferable to storage in solvent. Storage under inert argon atmosphere reduces losses more than all other conditions but could not prevent it entirely.