Scientific publications

Abstract Robotic handling and transfer printing of micrometer-sized superlight objects is a crucial technology in industrial fabrication. In contrast to the precise gripping with micropatterned adhesives, the reliable release of superlight objects with negligible weight is a great challenge. Slanted deformable polymer microstructures, with typical pillar cross-section 150 µm × 50 µm, are introduced with various tilt angles that enable a reduction of adhesion by a switching ratio of up to 500. The experiments demonstrate that the release from a smooth surface involves sliding of the contact during compression and subsequent peeling of the object during retraction. The handling of a 0.5 mg perfluorinated polymer micro-object with high accuracy in repeated pick-and-place cycles is demonstrated. Based on beam theory, the forces and moments acting at the tip of the microstructure are analyzed. As a result, an expression for the pull-off force is proposed as a function of the sliding distance and a guide to an optimized design for these release structures is provided.

Small organic molecules, like ethane and benzene, are ubiquitous in the atmosphere and surface of Saturn’s largest moon Titan, forming plains, dunes, canyons, and other surface features. Understanding Titan’s dynamic geology and designing future landing missions requires sufficient knowledge of the mechanical characteristics of these solid-state organic minerals, which is currently lacking. To understand the deformation and mechanical properties of a representative solid organic material at space-relevant temperatures, we freeze liquid micro-droplets of benzene to form ~10 μm-tall single-crystalline pyramids and uniaxially compress them in situ. These micromechanical experiments reveal contact pressures decaying from ~2 to ~0.5 GPa after ~1 μm-reduction in pyramid height. The deformation occurs via a series of stochastic (~5-30 nm) displacement bursts, corresponding to densification and stiffening of the compressed material during cyclic loading to progressively higher loads. Molecular dynamics simulations reveal predominantly plastic deformation and densified region formation by the re-orientation and interplanar shear of benzene rings, providing a two-step stiffening mechanism. This work demonstrates the feasibility of in-situ cryogenic nanomechanical characterization of solid organics as a pathway to gain insights into the geophysics of planetary bodies.

Micro-objects stick tenaciously to each other—a well-known show-stopper in microtechnology and in handling micro-objects. Inspired by the trigger plant, we explore a mechanical metastructure for overcoming adhesion involving a snap-action mechanism. We analyze the nonlinear mechanical response of curved beam architectures clamped by a tunable spring, incorporating mono- and bistable states. As a result, reversible miniaturized snap-through devices are successfully realized by micron-scale direct printing, and successful pick-and-place handling of a micro-object is demonstrated. The technique is applicable to universal scenarios, including dry and wet environment, or smooth and rough counter surfaces. With an unprecedented switching ratio (between high and low adhesion) exceeding 104, this concept proposes an efficient paradigm for handling and placing superlight objects. Nature teaches us how to design reliable grippers for moving and placing super-small objects that tend to stick to everywhere.

The manufacturing process defines not only the component’s geometry, but also how its surface senses and interacts with the outside world via its topography. Every manufactured surface is rough, but the component can benefit from the roughness control. Topography in functional surfaces is optimized either by controlling the manufacturing parameters or by post-manufacturing surface patterning technologies. However, how are topographic features measured and characterized? How do rough surfaces contact each other? What happens if fluid is present at the contact interface? And what are the mechanisms that correlate surface topography and its functionalities? This article will cover the engineering of surface topography in manufacturing by addressing empirical advancements and scientific understanding in the field. The functionalities covered are adhesion, friction, and convective heat transfer. Relatively large surface structures used for heat transfer mainly take advantage of recent advances in additive manufacturing, while conventional manufacturing processes and deterministic surface patterning techniques are discussed for the control of adhesion and friction.

MATLAB scripts were designed to compute the sample-limited spatial resolution in transmission electron microscopy (TEM) and scanning TEM (STEM) as a function of different microscopy parameters including the electron dose eD, sample geometry, and materials parameters. The scripts can be used to select the optimum microscopy modality and optimize the experimental conditions to achieve the best possible resolution considering the limitations set by both the electron optics and the examined sample. The resolution can be computed as function of the objective opening semi-angle α for TEM and detector opening semi-angle β for STEM. Optional code for computing a range over the sample thickness t or eD are provided as well, whereby the opening angle is optimized for each data point. The spatial resolution depends on the type of material of the nanoscale object (for example, gold or carbon nanoparticles), the type of matrix holding the objects (for example, water or ice), the depth of the nanoscale object inside the matrix, and eD. The optimization is consistent with the typical situation that carbon nanoparticles are best examined with TEM embedded in a thin matrix (t = 0.1 µm), while STEM is better suited for high atomic number objects such as gold nanoparticles in water, irrespective of t. The script also calculates the reduction of beam broadening in thick samples (t > 1 µm) using bright field STEM.

By differential thermal analysis, a concentration field suitable for the growth of Zr, Mg co-doped strontium hexagallate crystals was observed that corresponds well with known experimental results. It was shown that the melting point of doped crystal is ca. 60 K higher than that of undoped crystals. This higher melting points indicate hexagallate phase stabilization by Zr, Mg co-doping and increase the growth window of (Mg,Zr):SrGa12O19, compared to undoped SrGa12O19 that grows from SrO–Ga2O3 melts.

Metallic glasses are promising materials for micro-devices, where corrosion and friction limit their effectiveness and durability. We investigated nanoscale friction on a metallic glass in corrosive solutions after different immersion times using atomic force microscopy to elucidate the influence of corrosion on nanoscale friction. The evolution of friction upon repeated scanning cycles on the corroded surfaces reveals a bilayer surface oxide film, where the outer layer is removed by the scanning tip. Friction and adhesion after different immersion times in different solutions allow to compare the physicochemical processes of surface dissolution at the interfaces of the two layers. The findings contribute to the understanding of mechanical contacts with metallic glasses in corrosive conditions by exploring the interrelation of microscopic corrosion mechanisms and nanoscale friction.

Atomic-scale friction measurements were performed on a metallic glass in corrosive solutions using an atomic force microscope. An irregular stick-slip motion was observed and attributed to the amorphous structure of corroded surfaces. The friction data are interpreted based on the Prandtl-Tomlinson model by considering the disordered surface interaction potential. The transition between different stick-slip regimes, namely smooth sliding, slips over a basic lattice distance or multiple lattice sites, is a position-dependent characteristic on the amorphous surface. The stronger corrosion causes a significant increase in the probability of multiple slips accompanied by larger maximal forces and leads to a higher average friction. Our findings contribute to the understanding of atomic-scale friction on amorphous surfaces and fundamental friction mechanisms in corrosive conditions.

The tumor microenvironment plays an important role in cancer development and the use of 3D in vitro systems that decouple different elements of this microenvironment is critical for the study of cancer progression. In neuroblastoma (NB), vitronectin (VN), an extracellular matrix protein, has been linked to poor prognosis and appears as a promising therapeutic target. Here, we developed hydrogels that incorporate VN into 3D polyethylene glycol (PEG) hydrogel networks to recapitulate the native NB microenvironment. The stiffness of the VN/PEG hydrogels was modulated to be comparable to the in vivo values reported for NB tissue samples. We used SK-N-BE (2) NB cells to demonstrate that PEGylated VN promotes cell adhesion as the native protein does. Furthermore, the PEGylation of VN allows its crosslinking into the hydrogel network, providing VN retention within the hydrogels that support viable cells in 3D. Confocal imaging and ELISA assays indicate that cells secrete VN also in the hydrogels and continue to reorganize their 3D environment. Overall, the 3D VN-based PEG hydrogels recapitulate the complexity of the native tumor extracellular matrix, showing that VN-cell interaction plays a key role in NB aggressiveness, and that VN could potentially be targeted in preclinical drug studies performed on the presented hydrogels.

Assessing the safety of engineered nanomaterials (ENMs) is an interdisciplinary and complex process producing huge amounts of information and data. To make such data and metadata reusable for researchers, manufacturers, and regulatory authorities, there is an urgent need to record and provide this information in a structured, harmonized, and digitized way. RESULTS: This study aimed to identify appropriate description standards and quality criteria for the special use in nanosafety. There are many existing standards and guidelines designed for collecting data and metadata, ranging from regulatory guidelines to specific databases. Most of them are incomplete or not specifically designed for ENM research. However, by merging the content of several existing standards and guidelines, a basic catalogue of descriptive information and quality criteria was generated. In an iterative process, our interdisciplinary team identified deficits and added missing information into a comprehensive schema. Subsequently, this overview was externally evaluated by a panel of experts during a workshop. This whole process resulted in a minimum information table (MIT), specifying necessary minimum information to be provided along with experimental results on effects of ENMs in the biological context in a flexible and modular manner. The MIT is divided into six modules: general information, material information, biological model information, exposure information, endpoint read out information and analysis and statistics. These modules are further partitioned into module subdivisions serving to include more detailed information. A comparison with existing ontologies, which also aim to electronically collect data and metadata on nanosafety studies, showed that the newly developed MIT exhibits a higher level of detail compared to those existing schemas, making it more usable to prevent gaps in the communication of information. CONCLUSION: Implementing the requirements of the MIT into e.g., electronic lab notebooks (ELNs) would make the collection of all necessary data and metadata a daily routine and thereby would improve the reproducibility and reusability of experiments. Furthermore, this approach is particularly beneficial regarding the rapidly expanding developments and applications of novel non-animal alternative testing methods.