Energy Materials

Developing new flexible and electroactive materials is a significant challenge to producing safe, reliable, and environmentally friendly energy storage devices. This study introduces a promising electrolyte system that fulfills these requirements. First, polypyrrole (PPy) nanotubes are electropolymerized in graphite-thread electrodes using methyl orange (MO) templates in an acidic medium. The modification increases the conductivity and does not compromise the flexibility of the electrodes. Next, flexible supercapacitors are built using hydrogel prepared from poly(vinyl alcohol) (PVA)/sodium alginate (SA) obtained by freeze–thawing and swollen with ionic solutions as an electrolyte. The material exhibits a homogenous and porous hydrogel matrix allowing a high conductivity of 3.6 mS cm−1 as-prepared while displaying great versatility, changing its electrochemical and mechanical properties depending on the swollen electrolyte. Therefore, it allows its combination with modified graphite-thread electrodes into a quasi-solid electrochemical energy storage device, achieving a specific capacitance (Cs) value of 66 F g−1 at 0.5 A g−1. Finally, the flexible device exhibits specific energy and power values of 19.9 W kg−1 and 3.0 Wh kg−1, relying on the liquid phase in the hydrogel matrix produced from biodegradable polymers. This study shows an environment friendly, flexible, and tunable quasi-solid electrolyte, depending on a simple swell experiment to shape its properties according to its application.

Supercapacitors are fast-charging energy storage devices of great importance for developing robust and climate-friendly energy infrastructures for the future. Research in this field has seen rapid growth in recent years, therefore consistent reporting practices must be implemented to enable reliable comparison of device performance. Although several studies have highlighted the best practices for analysing and reporting data from such energy storage devices, there is yet to be an empirical study investigating whether researchers in the field are correctly implementing these recommendations, and which assesses the variation in reporting between different laboratories. Here we address this deficit by carrying out the first interlaboratory study of the analysis of supercapacitor electrochemistry data. We find that the use of incorrect formulae and researchers having different interpretations of key terminologies are major causes of variability in data reporting. Furthermore we highlight the more significant variation in reported results for electrochemical profiles showing non-ideal capacitive behaviour. From the insights gained through this study, we make additional recommendations to the community to help ensure consistent reporting of performance metrics moving forward.

Herein, we report the synthesis of TiO2–SnO2–C/carbide hybrid electrode materials for Li-ion batteries (LIBs) via two different methods of controlled oxidation of layered Ti2SnC. The material was partially oxidized in an open-air furnace (OAF) or using a rapid thermal annealing (RTA) approach to obtain the desired TiO2–SnO2–C/carbide hybrid material; the carbide phase encompassed both residual Ti2SnC and TiC as a reaction product. We tested the oxidized materials as an anode in a half cell to investigate their electrochemical performance in LIBs. Analysis of the various oxidation conditions indicated the highest initial lithiation capacity of 838 mAh/g at 100 mA/g for the sample oxidized in the OAF at 700°C for 1 h. Still, the delithiation capacity dropped to 427 mAh/g and faded over cycling. Long-term cycling demonstrated that the RTA sample treated at 800°C for 30 s was the most efficient, as it demonstrated a reversible capacity of around 270 mAh/g after 150 cycles, as well as a specific capacity of about 150 mAh/g under high cycling rate (2000 mA/g). Given the materials’ promising performance, this processing method could likely be applied to many other members of the MAX family, with a wide range of energy storage applications.

The fast growth of electric vehicles and electronic devices produces a mounting number of spent batteries which have reached their end of life. Therefore, it is essential to find a sustainable and efficient approach to battery recycling. Conventional recycling via high-temperature decomposition of the active components in the electrode material into elements level has the disadvantages of cumbersome operation, environmentally unfriendly, and high cost. Herein, one type of MXene material, annealed delaminated Ti3C2Tz (AD-Ti3C2Tz) electrodes, obtained by vacuum-assisted filtration and annealing processes, was directly used as free-standing anodes for both lithium-ion batteries and sodium-ion batteries without the use of binder or carbon additives. Electrochemical analysis showed that the non-diffusion-controlled redox reaction dominates the electrochemical behavior of the AD-Ti3C2Tz electrode. Furthermore, the AD-Ti3C2Tz electrode exhibits good electrochemical performance without adding conductive carbon in lithium-ion and sodium-ion batteries. For example, the lithium storage capacity was 89 mAh g−1 after 2000 cycles at a specific current of 1 A g−1. The sodium storage capacity is 108 mAh g−1 and 71 mAh g−1 at 0.02 A g−1 and 2 A g−1, respectively. After AD-Ti3C2Tz electrodes reach the end of their battery life, facile direct recycling processes were employed to recover the electrodes and the capacity recovery rate is above 90 %. Besides, the cycled MXene electrodes can be easily oxidized into TiO2/C hybrids with adjustable carbon content by changing the heat-treatment temperature in CO2 flow. The obtained TiO2/C could be widely applied in batteries and the electrocatalysis field, which realizes the second life of cycled MXene.

Carbon nanoparticle coatings on laser-patterned stainless-steel surfaces present a solid lubrication system where the pattern’s recessions act as lubricant-retaining reservoirs. This study investigates the influence of the structural depth of line patterns coated with multi-walled carbon nanotubes (CNTs) and carbon onions (COs) on their respective potential to reduce friction and wear. Direct laser interference patterning (DLIP) with a pulse duration of 12 ps is used to create line patterns with three different structural depths at a periodicity of 3.5 µm on AISI 304 steel platelets. Subsequently, electrophoretic deposition (EPD) is applied to form homogeneous carbon nanoparticle coatings on the patterned platelets. Tribological ball-on-disc experiments are conducted on the as-described surfaces with an alumina counter body at a load of 100 mN. The results show that the shallower the coated structure, the lower its coefficient of friction (COF), regardless of the particle type. Thereby, with a minimum of just below 0.20, CNTs reach lower COF values than COs over most of the testing period. The resulting wear tracks are characterized by scanning electron microscopy, transmission electron microscopy, and energy-dispersive X-ray spectroscopy. During friction testing, the CNTs remain in contact, and the immediate proximity, whereas the CO coating is largely removed. Regardless of structural depth, no oxidation occurs on CNT-coated surfaces, whereas minor oxidation is detected on CO-coated wear tracks.

When lubrication of rolling bearings with oil or grease is not possible, for example because the lubricant evaporates in vacuum, solid lubrication by multiwall carbon nanotubes (MWCNT) is a viable alternative. To understand the mechanisms underlying MWCNT lubrication of highly loaded contacts, we combine an experimental approach with large-scale molecular dynamics (MD) simulations. Tribometry is performed on ground iron plates coated with two different types of MWCNTs by electrophoretic deposition. Although structural differences in the MWCNT materials result in slightly different running-in behavior, most of the tests converge to a steady-state coefficient of friction of 0.18. The resulting wear tracks and tribolayers are subjected to structural and chemical characterization and suggest a tribo-induced phase transformation resulting in tribolayers that consist of MWCNT fragments, iron oxide, and iron carbide nanoparticles embedded in an amorphous carbon matrix. Covalent bonding of the tribolayer to the iron surface and low carbon transfer to the alumina counter body indicate sliding at the tribolayer/ball interface as the dominant mechanism underlying MWCNT solid lubrication. MD simulations of nascent a-C tribofilms lubricated by MWCNT bundles and stacks of crossed MWCNTs reveal two different sliding regimes: a low-load regime that leaves the MWCNTs intact and a high-load regime with partial collapse of the tube structure and formation of a-C regions. The critical load for this transition increases with the filling ratio of the MWCNT and the packing density of the stacks. The former determines the stability of the MWCNT, while the latter controls the local stresses at the MWCNT crossings. For both MWCNT materials, the high-load regime is predicted for the experimental loads. This is confirmed by a remarkable agreement between transmission electron microscopy (TEM) and atomistic simulation images. Based on the findings of this work, a multistep lubrication mechanism is formulated for MWCNT coatings rubbing against alumina on an iron substrate.

Stable and efficient SnO2 electrodes are very promising for effectively degrading refractory organic pollutants in wastewater treatment. In this regard, we firstly prepared Ti3+ self-doped urchin-like rutile TiO2 nanoclusters (TiO2-xNCs) on a Ti mesh substrate by hydrothermal and electroreduction to serve as an interlayer for the deposition of Sb−SnO2. The TiO2-xNCs/Sb−SnO2 anode exhibited a high oxygen evolution potential (2.63 V vs. SCE) and strong ⋅OH generation ability for the enhanced amount of absorbed oxygen species. Thus, the degradation results demonstrated its good rhodamine B (RhB), methylene blue (MB), alizarin yellow R (AYR), and methyl orange (MO) removal performance, with the rate constant increased 5.0, 1.9, 1.9, and 4.7 times, respectively, compared to the control Sb−SnO2 electrode. RhB and AYR degradation mechanisms are also proposed based on the results of high-performance liquid chromatography coupled with mass spectrometry and quenching experiments. More importantly, this unique rutile interlayer prolonged the anode lifetime sixfold, given its good lattice match with SnO2 and the three-dimensional concave–convex structure. Consequently, this work paves a new way for designing the crystal form and structure of the interlayers to obtain efficient and stable SnO2 electrodes for addressing dye wastewater problems.

Optimizing the synergy between nanoporous carbons and ionic liquids can significantly enhance the energy density of supercapacitors. The highest energy density has been obtained as the size of porous carbon matches the size of ionic liquids, while it may result in slower charging dynamics and thus reduce the power density. Enhancing energy storage without retarding charging dynamics remains challenging. Herein, we designed porous electrodes by introducing an optimized horn-like entrance to the nanopore, which can concurrently improve supercapacitors’ charging dynamics and energy storage. Our results revealed the mechanism of improved charging lies in the gradual desolvation process and optimized ion motion paths: the former expedites the adsorption of the counterion by reducing the transitional energy barrier for ions entering the pores, and the latter accelerates the co-ion desorption and eliminates ion overfilling. Meanwhile, the enhancement of energy density could be attributed to the multi-ion coordinated migration.

Inorganic-organic hybrid materials with redox-active components were prepared by an aqueous precipitation reaction of ammonium heptamolybdate (AHM) with para-phenylenediamine (PPD). A scalable and low-energy continuous wet chemical synthesis process, known as the microjet process, was used to prepare particles with large surface area in the submicrometer range with high purity and reproducibility on a large scale. Two different crystalline hybrid products were formed depending on the ratio of molybdate to organic ligand and pH. A ratio of para-phenylenediamine to ammonium heptamolybdate from 1 : 1 to 5 : 1 resulted in the compound [C6H10N2]2[Mo8O26] ⋅ 6 H2O, while higher PPD ratios from 9 : 1 to 30 : 1 yielded a composition of [C6H9N2]4[NH4]2[Mo7O24] ⋅ 3 H2O. The electrochemical behavior of the two products was tested in a battery cell environment. Only the second of the two hybrid materials showed an exceptionally high capacity of 1084 mAh g−1 at 100 mA g−1 after 150 cycles. The maximum capacity was reached after an induction phase, which can be explained by a combination of a conversion reaction with lithium to Li2MoO4 and an additional in situ polymerization of PPD. The final hybrid material is a promising material for lithium-ion battery (LIB) applications.

Multiple principal element or high-entropy materials have recently been studied in the two-dimensional (2D) materials phase space. These promising classes of materials combine the unique behavior of solid-solution and entropy-stabilized systems with high aspect ratios and atomically thin characteristics of 2D materials. The current experimental space of these materials includes 2D transition metal oxides, carbides/carbonitrides/nitrides (MXenes), dichalcogenides, and hydrotalcites. However, high-entropy 2D materials have the potential to expand into other types, such as 2D metal-organic frameworks, 2D transition metal carbo-chalcogenides, and 2D transition metal borides (MBenes). Here, we discuss the entropy stabilization from bulk to 2D systems, the effects of disordered multi-valent elements on lattice distortion and local electronic structures and elucidate how these local changes influence the catalytic and electrochemical behavior of these 2D high-entropy materials. We also provide a perspective on 2D high-entropy materials research and its challenges and discuss the importance of this emerging field of nanomaterials in designing tunable compositions with unique electronic structures for energy, catalytic, electronic, and structural applications.