Dr. Bart-Jan Niebuur

The structure of supraparticles (SPs) is a key parameter for achieving advanced functionalities arising from the combination of different nanoparticle (NP) types in one hierarchical entity. However, whenever a droplet-assisted forced assembly approach is used, e.g., spray-drying, the achievable structure is limited by the inherent drying phenomena of the method. In particular, mixed NP dispersions of differently sized colloids are heavily affected by segregation during the assembly. Herein, the influence of the colloidal arrangement of Pt and SiO2 NPs within a single supraparticulate entity is investigated. A salt-based electrostatic manipulation approach of the utilized NPs is proposed to customize the structure of spray-dried Pt/SiO2 SPs. By this, size-dependent separation phenomena of NPs during solvent evaporation, that limit the catalytic performance in the reduction of 4-nitrophenol, are overcome by achieving even Pt NP distribution. Additionally, the textural properties (pore size and distribution) of the SiO2 pore framework are altered to improve the mass transfer within the material leading to increased catalytic activity. The suggested strategy demonstrates a powerful, material-independent, and universally applicable approach to deliberately customize the structure and functionality of multi-component SP systems. This opens up new ways of colloidal material combinations and structural designs in droplet-assisted forced assembly approaches like spray-drying.

The tailored synthesis of copolymer architectures provides insights into fundamental structure–property relationships for the formation of complex morphologies through microphase separation. In this way, classical areas within the phase diagram can be specifically influenced and also adapted for important applications. The exploration of copolymer architectures also offers the possibility to discover entirely new morphologies. In this study, we design a symmetric dendrimer-like second generation block copolymer by anionic polymerization. The structural design of the polymers influences the curvature of the interfaces to produce, in particular, bicontinuous morphologies and is investigated based on molecular chain architecture. After extensive molecular analysis of the new dendrimer-like block copolymers, the resulting morphology is analyzed using transmission electron microscopy, atomic force microscopy, and small-angle X-ray scattering measurements. We further combine the experimentally obtained morphologies with Monte Carlo simulations to better understand the relationship between tailored polymer architecture and the observed morphology. By changing the volume ratio of the copolymers used and also mixing this complex polymer architecture with a linear block copolymer, we gain insights into the polymer behavior at the phase boundaries. This knowledge has an impact on the optical and mechanical properties of thermoplastic elastomers and their corresponding blends.

Trotz erheblichen Interesses an heteroatomhaltigen konjugierten Polymeren sind Beispiele mit schwereren Elementen des p-Blocks im Konjugationspfad rar. Die kürzlich beschriebene Metathese schwererer acyclischer Diene (HADMET) ermöglichte die Synthese eines Ge=Ge-Doppelbindungen enthaltenden Polymers, wenn auch eines unlöslichen mit begrenztem Polymerisationsgrad. Durch Einführung langer Alkylketten erhielten wir nun lösliche Vertreter mit – nach diffusionsabhängiger NMR-Spektroskopie (DOSY) und dynamischer Lichtstreuung (DLS) – nahezu unendlichen Polymerisationsgraden. UV/Vis und NMR-Daten bestätigen das Vorliegen von σ,π-Konjugation entlang der Silylen-Phenylen-Verknüpfungen zwischen den Ge=Ge-Einheiten. Günstige intermolekulare Dispersionswechselwirkungen führen zu leiterartigen, zylindrischen Aggregaten, wie durch Röntgendiffraktometrie (XRD), Kleinwinkel-Röntgenstreuung (SAXS) und DLS bestätigt. AFM- und TEM-Bilder abgeschiedener dünner Schichten offenbaren eine lamellare Anordnung ausgedehnter Polymerbündel.

Despite considerable interest in heteroatom-containing conjugated polymers, there are only few examples with heavier p-block elements in the conjugation path. The recently reported heavier acyclic diene metathesis (HADMET) allowed for the synthesis of a polymer containing Ge=Ge double bonds—albeit insoluble and with limited degree of polymerization. By incorporation of long alkyl chains, we now obtained soluble representatives, which exhibit degrees of polymerization near infinity according to diffusion-ordered NMR spectroscopy (DOSY) and dynamic light scattering (DLS). UV/Vis and NMR data confirm the presence of σ,π-conjugation across the silylene-phenylene linkers between the Ge=Ge double bonds. Favorable intermolecular dispersion interactions lead to ladder-like cylindrical assemblies as confirmed by X-ray diffraction (XRD), small angle X-ray scattering (SAXS) and DLS. AFM and TEM images of deposited thin films reveal lamellar ordering of extended polymer bundles.

We study the effect of additives on the colloidal stability of alkanethiol-coated gold nanoparticles. Cyclic amines and sulfides of different sizes were added to dispersions in decane at additive concentrations below 128 mM. Small-angle X-ray scattering (SAXS) indicated that tetrahydrothiophene reduced the agglomeration temperature, Tagglo, by up to 29 °C, a considerable increase in colloidal stability. Amines had a much weaker stabilizing effect of up to 2.5 °C. We found an unexpected maximum of stabilization for low additive concentrations, where Tagglo increased at concentrations above 64 mM. Molecular dynamics simulations were used to correlate these observations with the ligand shell structure. They excluded the physisorption of additives as a stabilization mechanism and suggested that sulfides replace hexadecanethiol on the AuNP surfaces by chemisorption. This hinders ligand ordering, thereby reducing Tagglo, which explains the stabilizing effect. Clustering of chemisorbed additive molecules at high concentration restabilized the ligand ordered state, explaining the detrimental effect of higher additive concentrations. The predictions of the simulations were confirmed by using thermogravimetric analyses and SAXS measurements of washed samples that indicated that the structure of the ligand shell itself, not the presence of physisorbed additives, changes Tagglo. Finally, we calculated potentials of mean force, which show that larger sulfide-based additives have a weaker affinity for the gold surface than smaller ones due to stronger steric hindrance. This explains why smaller cyclic sulfides were the most efficient stabilizers.

The development of hierarchically porous block copolymer (BCP) membranes via the application of the self-assembly and non-solvent induced phase separation (SNIPS) process is one important achievement in BCP science in the last decades. In this work, we present the synthesis of polyacrylonitrile-containing amphiphilic BCPs and their unique microphase separation capability, as well as their applicability for the SNIPS process leading to isoporous integral asymmetric membranes. Poly(styrene-co-acrylonitrile)-b-poly(2-hydroxyethyl methacrylate)s (PSAN-b-PHEMA) are synthesized via a two-step atom transfer radical polymerization (ATRP) procedure rendering PSAN copolymers and BCPs with overall molar masses of up to 82 kDa while maintaining low dispersity index values in the range of Đ = 1.13–1.25. The polymers are characterized using size-exclusion chromatography (SEC) and NMR spectroscopy. Self-assembly capabilities in the bulk state are examined using transmission electron microscopy (TEM) and small-angle X-ray scattering (SAXS) measurements. The fabrication of isoporous integral asymmetric membranes is investigated, and membranes are examined by scanning electron microscopy (SEM). The introduction of acrylonitrile moieties within the membrane matrix could improve the membranes’ mechanical properties, which was confirmed by nanomechanical analysis using atomic force microscopy (AFM).

The fabrication of nanocomposites containing magnetic nanoparticles is gaining interest as a model for application in small electronic devices. The self-assembly of block copolymers (BCPs) makes these materials ideal for use as a soft matrix to support the structural ordering of the nanoparticles. In this work, a high-molecular-weight polystyrene-b-poly(methyl methacrylate) block copolymer (PSb-PMMA) was synthesized through anionic polymerization. The influence of the addition of different ratios of PMMA-coated FePt nanoparticles (NPs) on the self-assembled morphology was investigated using transmission electron microscopy (TEM) and small-angle X-ray scattering (SAXS). The selfassembly of the NPs inside the PMMA phase at low particle concentrations was analyzed statistically, and the negative effect of higher particle ratios on the lamellar BCP morphology became visible. The placement of the NPs inside the PMMA phase was also compared to theoretical descriptions. The magnetic addressability of the FePt nanoparticles inside the nanocomposite films was finally analyzed using bimodal magnetic force microscopy and proved the magnetic nature of the nanoparticles inside the microphase-separated BCP films.

Abstract Block copolymers (BCPs) in the bulk state are known to self-assemble into different morphologies depending on their polymer segment ratio. For polymers with amorphous and crystalline BCP segments, the crystallization process can be influenced significantly by the corresponding bulk morphology. Herein, the synthesis of the amorphous-crystalline BCP poly(dimethyl silacyclobutane)-block-poly(2vinyl pyridine), (PDMSB-b-P2VP), by living anionic polymerization is reported. Polymers with overall molar masses ranging from 17 400 g to 592 200 g mol−1 and PDMSB contents of 4.8–83.9 vol% are synthesized and characterized by size-exclusion chromatography and NMR spectroscopy. The bulk morphology of the obtained polymers is investigated by means of transmission electron microscopy and small angle X-ray scattering, revealing a plethora of self-assembled structures, providing confined and nonconfined conditions. Subsequently, the influence of the previously determined morphologies and their resulting confinement on the crystallinity and crystallization behavior of PDMSB is analyzed via differential scanning calorimetry and powder X-ray diffraction. Here, fractionated crystallization and supercooling effects are observable as well as different diffraction patterns of the PDMSB crystallites for confined and nonconfined domains.

Self-healing nanocomposites can be generated by organic functionalization of inorganic nanoparticles and complementary functionalization of the polymer matrix, allowing reversible interactions between the two components. Here, we report on self-healing nanocomposites based on ionic interactions between anionic copolymers consisting of di(ethylene glycol) methyl ether methacrylate, sodium 4-(methacryloyloxy)butan-1-sulfonate, and cationically functionalized iron oxide nanoparticles. The materials exhibited hygroscopic behavior. At water contents < 6%, the shear modulus was reduced by up to 90%. The nanoparticle concentration was identified as a second factor strongly influencing the mechanical properties of the materials. Backscattered scanning electron microscopy and small-angle X-ray scattering measurements showed the formation of agglomerates in the size range of 100 nm to a few µm in diameter, independent of concentration, resulting in the disordering of the semi-crystalline ionic polymer blocks. These effects resulted in an increase in the shear modulus of the composite from 3.7 MPa to 5.6 MPa, 6.3 Mpa, and 7.5 MPa for 2, 10, and 20 wt% particles, respectively. Temperature-induced self-healing was possible for all composites investigated. However, only 36% of the maximum stress could be recovered in systems with a low nanoparticle content, whereas the original properties were largely restored (>85%) at higher particle contents.

Anionic polymerization for the preparation of polystyrene-b-polybutadiene is well-established and leads to thermoplastic elastomers on industrial scale. The classical ABA block copolymer (BCP) architecture and composition usually forms a cylindrical morphology in the bulk state. Their anisotropic mechanical properties are, however, unfavorable for many applications. The gyroid microphase is entirely isotropic, but it is only formed in a narrow compositional area of around 35 vol% of the minority polymer block. In the present study, a second-generation dendrimer-like block copolymer structure ((AB)2B)3 is described. This BCP architecture is expected to show a higher curvature on the microphase boundaries, which leads to a larger morphological range for the gyroid phase. Three compositionally different polymers are synthesized by living anionic polymerization strategies and the resulting morphology is analyzed via transmission electron microscopy (TEM) and small angle X-ray scattering (SAXS). The dendrimer-like BCPs are compared to their less branched analogues, namely the asymmetric star polymers and H-shape stars. The expected influence of the dendrimer-like BCP architecture on the microphase separation is investigated paving the way to a promising synthetic platform for interesting mechanical and optical properties.